Controllers
| Time Percentage Controller | Bulb & Capillary Controller | |||||||||||||||||||||||||
![]() |
![]() |
|||||||||||||||||||||||||
|
Specifications: • 120 or 240 VAC • 15 amps • Portable, plug and play design • 6' power cord with 2 pole 3 wire plug and receptacle • Designed for indoor use |
Specifications: • 120 or 240 VAC • 15 amp • Portable, plug & play design • Copper bulb & capillary, 4' long • 6' power cord with 2 pole 3 wire plug and receptacle • Designed for indoor use |
|||||||||||||||||||||||||
This controller varies the proportion (length) of time the heater is in the "on" or "off" heating mode. the heating application will deteremine the actual percentage setpoint required. The controller does not use a temperature sensor and therefore satisfactory operation requires occasional supervision under changing load conditions. |
Bulb Dimensions 3/8" diameter x 4" long |
| Thermostat | Thermostat | |||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||||||||||||
| Specifications: • 25 amps up to 277 VAC (UL) • 25 amps up to 240 VAC (CSA) • Surface mount • 4' power leads • Single Pole Double Throw |
Specifications: • 25 amps up to 277 VAC (UL) • 25 amps up to 240 VAC (CSA) • Surface mount • 4' power leads • Single Pole Double Throw • 1/2" NPT flexible conduit fitting |
|||||||||||||||||||||||||||||||||||||||||||||||||
|
|
| Thermocouple Controller | Bulb and Capillary - Outdoor Use | |
![]() |
![]() |
|
| Specifications: • 120 or 240 VAC • 15 amps • Temperature Ranges 0-175°, 0-500°, or 0-999°F • Plug-in operation • Type K thermoucouple • Proportional controlling • 8' power cord 2 and 4-pin plug assembly |
Specifications: • Rated 22 Amps up to 277 VAC • Differential 6° F • Enclosure rates NEMA 3R, for outdoor use • Tinned copper bulb and capillary, 10' long • Single Pole Double Throw contacts • Three different temperature ranges: 0-150°F, 100-250°F, or 200-350°F |
|
| The
Thermocouple Controller is designed for indoor, general purpose use, to
control the temperature of small tanks, drums, pipes, or other applicatins
requiring automatic control. The low temperature range of the controller
makes it ideal for use with plastic drums, tanks, or pipes. |
This
controller has an oil filled bulb and capillary and is used where weatherproof
enclosures are necessary. It is designed to maintain the required
temperatures in heat tracing systems, freeze protection systems, process
systems, and moisture protection systems. |
| Hazardous Area Bulb and Capillary | |
![]() |
Approvals: UL Hazardous Locations Class 1, Division 1 & 2, Groups B, C, & D Class 2, Division 2, Groups E, F, & G Class 3 CSA Class 1, Division 1 & 2, Groups C & D Class 2, Division 2, Groups E, F, & G Class 3 |
Specifications: • Rated 22 Amps up to 480 VAC • 304 SS Bulb and Capillary, 10' long • Single Pole Double Throw contacts • Enclosure rated NEMA 7 & 9 • Repeatablility 1% of range |
The
Hazardous Area Bulb and Capillary controllers are oil filled bulb and
capillary temperature controllers used for controlling individual circuits
in environments requiring explosion enclosures. These controllers
are designed to maintain the required temperature in heat tracing, freeze
protectin and process maintenance applications |
|
Ambient Sensing
|
|||||||||||||||
|
Single Set Point Control
|
|||||||||||||||
Dual Set Point Control
The Dual Controller has two independent set-point dials and two independent SPDT contracts allowing two different temperature set points. |
Email for product information / pricing to: protherm@comcast.net