PYROJACKET™

Constructed from a high bulk fiberglass sleeve heavily coated with iron oxide red silicone rubber, Pyrojacket sheds molten metal splash and withstands intense heat and flame, making it ideal for protecting hoses, cable and tubing in a variety of hostile environments. Withstands continuous exposure to 500°F (260°C), up to 2000°F (1090°C) for 15-20 minutes, and up to 3000°F (1650°C) for 15-30 seconds. Available in sizes up to 5" (127 mm) diameter, Pyrojacket has an excellent modulus of elasticity and can be used to bundle hoses and cables.  Pyrojacket's insulation properties allow it to provide effective burn protection for personnel from hot hoses and piping, while reducing costly heat energy losses. Available in both Industrial and Aerostyle grades.

PYROJACKET™ VCO

Pyrojacket VCO option is the solution to shutting down equipment and disconnecting hoses and cables to install heat protective sleeving.  The VCO option is factory installed, to ensure correct fit and structural integrity. Using high temperature fiberglass thread, a flame retardant hook and loop closure is sewn internally. Pyrojacket VCO is adjusted for size, to allow for the overlap where hook and loop closures meet.  Pyrojacket VCO is available in sizes from 3/4" (19 mm) to 4-1/2" (115 mm) diameter.

LARGE DIAMETER FABRICATED PYROJACKET™

Large Diameter Fabricated Pyrojacket is constructed by sewing 96 oz. Pyroblanket along the edge with high temperature resistant glass fiber thread. Since 96 oz. is our heaviest graded of molten splash and flame resistant cloth, the resultant fabricated Pyrojacket is a robust, heavy grade sleeve suitable for the most demanding applications.  Large Diameter Fabricated Pyrojacket can be supplied in any custom length. Typical diameters range from 5" (127mm) up to 24" (610mm).

SILICAFLEX™ SLEEVE

Constructed from an Amorphous Silica (SiO²) fiber yarn, Silicaflex sleeve is suitable for continuous use at 1800°F (982°C) and able to withstand short term exposure up to 3000°F (1650°C), Silicaflex sleeves set the standard for flexibility and minimum lineal shrinkage under high heat conditions. Silicaflex fibers are resistant to most industrial chemicals except hydrofluoric acid, phosphoric acid and strong alkalis. Silicaflex sleeve is completely flameproof and its high silica purity content of over 96% allows it to protect hoses and cables in the hottest environments.  All Silicaflex fibers retain their strength and flexibility through repeated exposures to high temperatures, and have a dielectric strength of 40V/mil making Silicaflex products ideal for insulating electrical leads and instrumentation wires.

THERMOSLEEVE™ B

A heavy wall braided fiberglass sleeve capable of operating at a continuous temperature of 1000°F (538°C). Thermosleeve B's excellent insulation capabilities and low cost make it a good choice as economical hose and cable protection where molten splash is not a factor.  The texturized untreated construction allows for Thermosleeve B to exhibit excellent resistance to thermal conductivity, making it a good choice for use by itself or under other sleeve products like Pyrojacket, Pyreflect or Silicaflex in applications where additional thermal insulation is required.

THERMOSLEEVE™ S

An expandable braided fiberglass sleeve that will cover a wide range of sizes. Thermosleeve S is heat cleaned and coated with an acrylic saturant to further reduce loose fibers, enhance handling characteristics and improve abrasion resistance.  Thermosleeve S will expand and contract by approximately 25% of its nominal size, and will operate continuously at 1000°F (538°C). The acrylic saturant begins to decompose at approximately 400°F (204°C), but does not affect the performance of the sleeve.  Due to its wide range of expansion and contraction, Thermosleeve S is offered in just 4 sizes, which cover all diameters from 3/8" (10 mm) up to 3-1/2" (89 mm).

PYREFLECT™ SLEEVE

Pyreflect sleeve is fabricated from Pyreflect blanket, and constructed by folding the blanket over and sewing along the edge. The edge seams are sewn using high temperature fiberglass thread, and are double-stitched for extra strength.  It is the ideal choice for protecting critical hoses, cables or alarm circuitry from occasional flame or radiant heat.  Pyreflect sleeve can be supplied in any diameter from 3/8"(10 mm) up to 12" (305 mm). It can also be supplied with a VCO option where a high temperature hook and loop closure system is sewn inside the sleeve to allow it be installed without disconnecting hoses or cables.